Custom Fixed Knot Fence Specifications

Your Fence,
Your Specifications

Not every paddock fits a catalogue item. We work directly with you to specify height, wire diameter, stay spacing, coating, roll length and packing for the intended application.

Request a Custom Quote → View Standard Sizes
Every standard size we list is a starting point, not a hard limit. Whether you need a taller deer fence, a shorter stay spacing for goats, a specified coating, or a non-standard roll length — we can manufacture to the signed specification and check finished dimensions in the factory.

1 Six Parameters You Control

These are the dimensions we adjust on every custom order. You can change one of them or all six — we'll build a compliant specification around your requirements.

📏

Fence Height

600 mm – 2 400 mm

Standard heights run from 700 mm to 1 900 mm. Go lower for aquatic or specialty use, higher for exclusion or security fencing. Tell us the animal and the pressure, and we'll recommend the right height.

〰️

Number of Line Wires

4 – 17 wires

More line wires = denser fabric and higher vertical load distribution. Critical for small livestock, vermin exclusion, or deer. Fewer wires reduce cost where pressure is low and aperture size is less critical.

⬛

Stay Spacing

100 mm · 150 mm · 300 mm · Custom

Vertical stays hold fence shape and resist stock pressure. 300 mm is standard for cattle and sheep. 150 mm for goats and high-pressure use. 100 mm or less for pigs and vermin exclusion.

🔩

Wire Diameter

2.0 mm – 4.0 mm line wire

Heavier gauge increases breaking load and impact resistance — suited for deer, cattle pressure, or perimeter security. Lighter gauge reduces roll weight and cost where livestock pressure is moderate.

🛡️

Coating Type & Class

HDG W7 · W10 · W15 · Zn-Al

Coating mass is one factor in corrosion protection. The final coating option should follow the buyer's requirement, site conditions and applicable specification.

🧵

Roll Length

25 m – 500 m per roll

Standard rolls are 100 m or 200 m. Short rolls (25–50 m) reduce offcuts on irregular paddocks. Long rolls (250–500 m) cut installation joins and handling time on large stations.

2 How to Read a Fence Designation

Every fixed knot fence product — standard or custom — is described by a three-part designation. Once you understand it, you can specify exactly what you need, or verify that a product matches your requirements.

8 / 90 / 30
e.g. 8/90/30 = most popular all-stock boundary fence
8 Line Wires
/
90 Height (cm)
/
30 Stay Spacing (cm)

Custom designations

A custom order simply uses non-standard numbers in the same format. If you need a 1 200 mm fence with 10 line wires and 150 mm stays, the designation becomes 10/120/15. We quote and produce it against the approved specification.

3 Choose by Application

Match your livestock, terrain, and environment to a starting specification. These are recommended baselines — we refine them with you based on site conditions, paddock size, and pressure levels.

Animal / Application Height Stay Spacing Min. Wire Ø Coating
Sheep — boundary 800 – 900 mm 300 mm 2.5 mm HDG W10
Sheep & Cattle — mixed stock 900 mm 300 mm 2.5 mm HDG W10
Cattle only — paddock 900 mm 300 mm 3.0 mm HDG W10
Goats 1 000 – 1 150 mm 150 mm 2.5 mm HDG W10
Pigs 900 – 1 000 mm 100 mm 3.0 mm HDG W10
Equine (horses) 1 200 – 1 500 mm 100 mm 3.0 mm HDG W10
Deer 1 800 – 1 900 mm 150 – 300 mm 2.5 mm HDG W10
Wild dogs & foxes 900 – 1 150 mm 100 – 150 mm 2.5 mm HDG W10
Kangaroo exclusion 1 500 – 1 800 mm 150 mm 2.5 mm HDG W10
Coastal AU / all NZ sites As required As required 2.5 mm Zn-Al recommended
Large station — long spans 900 mm 300 mm 3.0 mm HT HDG W10
Non-standard / special project Custom Custom Specify Discuss with us
🗺️

Australia Corrosion Zones — Wire Coating Guide (AS/NZS 4534)

Not sure which coating is right for your location? Find your corrosion category and see the recommended HDG or Zn-Al class for your site.

→

4 Coating — The Most Important Decision

Coating selection is an important part of long-term fence performance. Actual service life depends on coating composition and mass, exposure, handling, installation and maintenance.

We offer two coating systems, both manufactured to AS/NZS 4534:

🔩 Hot-Dip Galvanized (HDG) · Z Coating
  • Pure zinc coating to AS/NZS 4534
  • Available in Class W7, W10, or W15
  • W10 (≈ 240 g/m²) recommended as minimum for rural use
  • Proven 25–40 year service life in standard inland environments
  • Lower unit cost — best value for most AU inland paddocks
  • W15 available for moderately aggressive or high-value installations
✓ Best for: Inland Australia · Low humidity · Standard rural fencing
🌊 Zinc-Aluminium Alloy (Zn-Al) · ZA Coating
  • Zinc / 10% aluminium alloy coating per AS/NZS 4534
  • Available where the buyer specifies a zinc-aluminium alloy coating
  • Superior adhesion at knot joints — resists chipping under load
  • Recommended across most of New Zealand
  • Essential for coastal AU, high humidity, and acid soils
  • Higher upfront cost — lower total lifetime cost per metre
✓ Best for: Coastal AU · New Zealand nationwide · High humidity · Marine-adjacent

Above-standard coating mass available

For critical infrastructure or unusually aggressive environments, we can specify coating mass above the standard W15 class. Share your site conditions and we'll advise the right specification.

5 How a Custom Order Works

Custom specifications go through the same production and QC process as our standard range — the only difference is the dimensions. Here's how the process runs from enquiry to delivery.

Tell Us Your Requirements

Share your animal type, paddock environment, required height, coating preference, and approximate quantity. Rough figures are fine — we'll help refine them.

We Propose a Specification

We review the application and respond with designation, coating and roll options for discussion. The final specification is confirmed with the buyer before production.

Sample Before You Commit

Where practical, sample arrangements can be discussed so the buyer can review wire diameter, knot quality and finish before a production order.

Production & Delivery

Custom production runs follow the approved specification. Required inspection and documentation should be agreed before order confirmation.

⏱
Response Time
Within 24 hrs
📦
Samples
Before you commit
🔬
Documentation
Full certs included
🚢
Delivery
AU & NZ, on-schedule
🤝
Minimum Order
Flexible — ask us

6 Request a Custom Quote

Fill in as much as you know. Even a rough requirement is enough to start; we will review it and respond with the next information needed for specification and quotation.

We review each enquiry and respond with specification questions, quotation information or sample options as applicable.

Not Sure Where to Start?

Tell us your animal, environment and current specification. We will prepare a specification and container-quotation comparison for review.